Do It Yourself Bathtub Installation.
Do It Yourself Bathtub Installation.
Blog Article
Were you interested in facts concerning Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't exactly rocket science, however it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is easily obtainable, the task can move quickly; if you have to open a wall to eliminate the old bathtub and also place the new bathtub, the job is much harder. In either situation, the task is within a home handyman's skills, although you will certainly need a helper to leave the old bathtub and set in the brand-new one. Make sure you have actually certified on your own for the work and fit trying it. Rather than employing a contractor to take over a halfway-completed task, it is better to think about utilizing one prior to you start. Possibilities are you might need a specialist plumber to make tube connections.
This article will certainly aid you set up a new bath tub in your washroom if you have currently bought a new tub as well as don't require to alter the setup of your previous water pipelines.
Your devices and also material checklist should comprise the following:
Getting ready for the Setup
First of all, the sustaining frame supplied with the bath should be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to stop stress on the tub.
Fit the flexible tap connectors to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must now prepare to be suited its final position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited access that is often the instance.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric all set for the staying water that will certainly originate from the pipelines. When the supply pipelines have actually been removed, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning during this procedure. Once the faucets have been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old securing substance.
Before going on to fit the new taps, contrast the pipeline connections on the old faucets to the new faucets. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Using the two wooden boards under its feet, place the bathtub in the called for setting. The wood boards are handy in uniformly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the level and changing the feet on the bath tub until the spirit level reads degree.
To install taps, fit all-time low of the outermost adaptable tap port to the appropriate supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Switch on the water and inspect all joints and also new pipework for leakages and also tighten them if required. Load the bathtub and additionally check the overflow outlet as well as the regular outlet for leaks.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and also sealing around the bathtub must wait till the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will need a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the various other end provides a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin making sure that the washing machines remain in place between the faucet and also the sink. Protect the faucet in position with the manufacturer given backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular tap ports. The previous kind should be connected to the tap ends first, tightening up only by hand. The supply pipes can later be linked to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to crack an inflexible seal, triggering the water to permeate the wall in between the bath and the tiling, leading to difficulties with moisture as well as possible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are sold in tubes and also cartridges, and also are capable of sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the bath tub with water prior to sealing, to enable the movement experienced when the bathtub remains in use. The sealer can split relatively early if you do not think about this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water-proof sticky and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
We had been made aware of that editorial about Installing A Bathtub through a friend on another web address. Sharing is caring. Helping people is fun. Bless you for your time. Visit us again soon.
Appointment Report this page